OSHA Daily Safety & Fall Protection Checklist
Generate a customized daily roofing safety checklist using federal OSHA, state-plan, or Canadian jurisdiction guidance. Review the cited source, adapt the checklist to the site, and download a branded report without signing up.
- Fall-protection trigger: 6 ft ()
- Regulation: California Code of Regulations, Title 8, Construction Safety Orders (CCR T8, s.1671.1, 1730-1731)
- Written plan: Written fall-protection plan required when conventional fall protection (guardrails, PFAS, nets) is infeasible or creates a greater hazard (1926.502(k)).
- • Effective July 1, 2025, Cal/OSHA lowered the fall-protection trigger for residential roofing from 15 ft to 6 ft — matching federal OSHA. Follow the stricter 6 ft rule for re-roofing until formal clarification.
Federal/state trigger: 6 ft (California residential now 6 ft)
Your free RoofHQ report
Download, share, print, copy, or email it instantly. No signup required.
Branded “Powered by RoofHQ”
Fall Protection — REQUIRED at 6 ft (California)
- Threshold applies per California Code of Regulations, Title 8, Construction Safety Orders (CCR T8, s.1671.1, 1730-1731)
- Select and document the compliant fall-protection system for each exposed work area
- If guardrails are used: inspect top rails, mid-rails, toeboards, posts, and all open sides before work
- If a personal fall-arrest system (PFAS) is used: inspect harness, connectors, lifeline/lanyard, D-ring, and anchor points before each use
- LOW SLOPE (4:12 or less): select a compliant system under 29 CFR 1926.501(b)(10); warning-line and monitoring options have specific limits
- SKYLIGHTS: covers rated for 2× impact load AND/OR guardrails on every skylight — workers can fall through 'solid-looking' covers
- Anchor points re-verified by competent person today
Ladder & Access Safety
- Ladder extends 3 ft above landing surface and is secured/anchored
- Ladder set at 4:1 angle (1 ft out per 4 ft up), on stable level footing
- Duty rating matches combined worker + tool load (Type IA = 300 lb recommended for roofing)
- Crew of 4: one worker on ladder at a time, 3-point contact enforced
Daily Site & Crew Briefing
- Competent person documented today's inspection (4-person crew signed acknowledgment)
- Weather checked and the company severe-weather stop-work policy reviewed
- First-aid kit stocked and location known to all workers
- New/hazarded workers received fall-protection training (documented)
Job Site Hazards
- Power lines located — minimum clearance maintained from ladders/equipment
- Debris/chute area barricaded below; drop zone flagged
- Walking/working surfaces free of shingle granules, dust, and tools (slip/trip check)
- Material staging: shingle bundles distributed per roof truss load limits, never stacked at ridge
This generator is a training aid, not legal advice. Always defer to your competent person and the current OSHA standard for California. Review OSHA 1926.501
Know which fall-protection rule applies to your job site
- United States: federal OSHA requires fall protection at 6 ft in construction (29 CFR 1926.501), including residential work. Some states operate OSHA-approved plans that must be at least as effective as federal OSHA and may add requirements. California's updated residential roofing rule became effective July 1, 2025.
- Canada: fall protection is regulated provincially. Most provinces trigger at 3 metres (~10 ft). Alberta adds a 1.2 m guardrail rule for permanent work areas; BC requires a written plan at 7.5 m+; Ontario mandates Working at Heights training and a 2.4 m threshold in some situations.
- Height is not the only question. Openings, skylights, dangerous equipment, steep slopes, work methods, and lower-level hazards can change which controls apply. Select your jurisdiction above, review the cited source, and have the competent person approve the site-specific plan.
A daily paper trail generated before the first ladder goes up is the cheapest insurance policy in roofing — and this tool takes about 20 seconds each morning. Generated PDFs and checklists are branded with RoofHQ.
Run the same discipline on the roof itself: a Download the roof condition assessment from attic to ridge cap catches the hazards — skylights, fragile decking, and openings — that the fall-protection plan has to address.
Keep the crew safe—and keep the job moving.
RoofHQ keeps each roofing job, takeoff, proposal, and payment status in one contractor workflow.